Tay’s homemade chopper trike – England

Tay helped his dad build this chopper trike from scrap bike parts.

Submitted by AtomicZombie forum member and bike builder, Naughtyboy.

“We built this because my youngest two kids needed bigger bikes and they both love workshop time with daddy.

One of the kids from school turned up on a shop built chopper, so Tay looked it over and said, “Me and my dad can build (one) better.”

We’ve built all sorts from scrap wood and metal and they have even helped me with rebuilding an old Land rover.

Tay decided he wanted a trike after seeing my Gladiator (chopper trike) plans, and he also looked through my 15 other plans to plan future bikes. The front is based on the Gladiator chopper trike and the rear, I think, was based on the DeltaRunner Recumbent Trike, but flipped over.

The forks are made from 16mm od x 8mm id blow pin shafts left over from machine re-furb at work. Suspension is made of old trampoline springs I found. The handlebars are from an old rotavator which I’m planning on using engine on quad-cycle (so many ideas, so little time).

I had to turn some sleeves to fit them as id was bigger than od of forks. Tay helped with drilling on lathe. Front wheel is 20″ and back started as the same size, but are now 26″ as we needed the smaller one for his little sister’s trike.

I just wish he would let me finish painting it, but he’s too busy racing on the road with his mates! I am impressed with how tight a turning circle it as and how fast he can go.”

Read more about this project at the builders forum:
http://forum.atomiczombie.com/showthread.php/9247-happy-boy

More pictures in the bike builders gallery:
http://forum.atomiczombie.com/gallery/browseimages.php?do=member&imageuser=5871

www.AtomicZombie.com
Advertisements

Bike builders newsletter online – Oct 30

bike builders news

Feature article by David Monk: Building the AtomicZombie Warrior Trike

Parts for your bike projects: axle adapters, disc brake adapters, hub flanges, head tubes and bottom brackets

Bike builders community: Hot topics and intriguing conversations.
Bike builders gallery: New additions. Upload your own photos.
Bike builders feedback: We love to hear from you.

Free DIY tutorials: Many in PDF format
AZTV webisode: There and Back Again: A Zombie’s Tale

This and archived newsletters are here: http://atomiczombie.com/NewsLetters.aspx

 

diy bike plans

The HammerHead Winter Trike

hammerhead winter trike
Hammerhead winter trike

 

 

This simple DIY project is designed to inspire you to build a bike to conquer a typical winter climate with snow, ice and slush. The Hammerhead is a two-headed monster that eats snow and ice for breakfast, and has no fear of Old Man Winter or his frozen wrath.

I designed this two headed bike to give myself a way of staying in shape during the winter months. I used to take my fancy, overpriced mountain bike out for winter rides, but soon realized that it wasn’t suitable in deep snow or around icy corners, and the bike was taking a lot of abuse every time I bit the dust (snow).

Obviously, a three-wheeled bike was necessary to maintain balance, so I rebuilt one of those old-style trikes (the kind with two wheels and a big basket in back) and tried to make it as light as possible by removing all parts that weren’t needed, and then added some knobby tires for better traction. The results were very disappointing; not only was this bike as heavy as a tank, but it also had no traction at all. Because that style of trike only drives one of the rear wheels, it mainly just spun around on most surfaces except bare pavement. Adding a differential (a gear system to spin both wheels and transfer power between them) was just too complicated and would add even more weight, so I decided to scrap this type of approach.

My new plan was to have two front wheels for stability and one rear driving wheel for traction. The two wheels up front (tadpole style) design is popular on low-slung recumbent trikes, making them very fast and comfortable, but it is not a suitable design for a winter bike for several reasons.

First, you don’t want to be slung two inches from the slushy ground while winter riding because you will get very wet from wheel spray.

Second, most people driving motorized vehicles will not normally expect to see bicycles in the winter months, so you want to be as visible as possible. A low recumbent trike is not very visible to drivers of motorized vehicles.

Third, is road salt. If you live in a community that routinely uses salt on roads and sidewalks, then this is a problem because salt will corrode metal. Why spend so much and money on something that will require many custom-made parts, and will end up rusted at the end of the year?

Hammerhead is not only as high as a regular bike, but it needs only regular bike parts and a little welding here and there. The design uses a regular mountain bike with two head tubes welded on each side of the frame in order to support two sets of front forks and wheels. Both wheels steer at the same time just like skis on a snow machine. In fact, the steering linkage that I scavenged is from a snow machine!

The trike is called Hammerhead because I thought the finished frame looked something like a hammerhead shark. You see it too, right?

Parts You Will Need

Now that you have a plan and a desire to conquer winter, let’s start by gathering some parts. As shown in Figure 1, you will need a complete mountain bike (stripped down to the frame), two front wheels, two head tubes (ground clean) and a matching pair of front forks. The critical requirement here is that both head tubes, forks, and front wheels be identical or very close in size. Even the tires should be the same, as any mismatch will cause the final bike to be uneven and wobbly.

bicycle parts for the winter trike
Figure 1 — Gathering parts for the Hammerhead trike.

 

 

The first step is to create the two head tube extensions. Each head tube is welded to a pair of 12-inch lengths of one inch diameter thin walled electrical conduit, or similar bicycle frame tubing. These two tubes are then welded to each side of the original head tube on the frame. Both tubes are welded at exactly 90 degrees to the head tube, as shown at the top in Figure 2.

If the original head tube is not as tall as the two new head tubes, position the new extension tubes so that they are able to mate to the original head tube. To make a good weldable joint, fishmouth the ends of the tubing to conform to the round edge of the head tube as shown in the lower part of Figure 2.

Weld carefully, tack welding only at first to ensure that the two tubes end up at 90 degrees to the head tube. Any error here will result in a front wheel misalignment, so check the angles with a 90 degree square as you work. Look ahead to see how the extension tubes will place the two new head tubes at the same angle as the original head tube and at 90 degrees to the frame tubing.

hammerhead trike has two head tubes
Figure 2 — Creating the two head tube extensions.

 

 

When you have both head tubes welded to their two 12-inch tubes, it’s time to weld them to the original head tube on the donor frame.

As shown in Figure 3, the extension tubes are welded to the original head tube so that all head tubes are at the same angle and so that the extension tubes are at 90 degrees to the frame tubing. You want each head tube to end up at the exact same angle as the middle head tube so that the caster angle remains the same as it was on the original bike. If you imagine two identical bikes standing side by side, then you can picture what we want here.
At this point, just make a few good tack welds around the joint to secure all of the pars together. A final alignment check will be made by installing the forks and front wheels to compare them with each other.

align the head tubes
Figure 3 — Weld the head tubes so that all three align.

 

 

To ensure that the two head tubes are aligned with each other, put the bearings, rings, and forks on both sides and then install the two front wheels. Remember that both front wheels must be the same diameter, which is why both tires should be the same type. When you have both wheels installed, stand up the bike and place both forks in the straight ahead position for a visual inspection. With the parts only tack welded, you can probably make slight alignment adjustments by tapping with a mallet.

Once you are certain that both head tubes are aligned, weld around all of the joints, following the same order on both sides so that any distortions happen equally.

check fork and wheel alignment
Figure 4 — Checking alignment using the front forks and wheels.

 

 

To make this frame structurally sound, a set of trusses will be added to the front in order to triangulate the frame. The frame is somewhat rigid as it sits, but any hard force to either front wheel could bend the frame at the joint between the head tube and the new extension tubing.

With some simple trussing, we form a triangle on each side, making the frame extremely strong. Any tube with a diameter between half an inch and 1 inch will do for the trussing. I found some old lawn furniture with 3/4 inch tubing and cut a few pieces to make the trusses.

These trusses are welded from the top of each head tube to somewhere near the middle of the top tube on the main frame. The trussing should be installed a few inches head of where your knee will be when you are pedaling the bike. To find this spot, put on a crank arm and set the seat to your height, then mark it on the frame while you pedal. The main goal is to make sure your knee does not hit the tube.

truss tubing increases frame strength
Figure 5 — The truss tubing makes the frame very strong.

 

 

Stay tuned for more on this project. Part 2 coming soon.

 

AtomicZombie bike plans

The time and space conundrum

Our basement before any renos were done

 

Time and space are those two things that have always managed to stump the world’s greatest thinkers, leaving us to the stark realization that we are but visitors on this rock, hurling through time and space at 66,000 miles an hour, tethered to a burning sphere by an invisible force in an unfathomable universe. This most of us take for granted, while refusing to believe these forces have any more effect on us than a butterfly beating its wings halfway around the world.

Yeah, I stole that quote from the X-Files and my mention of time and space here is under a different context, a more literal one; most of us need more free time and a larger space to work in! I am constantly trying to find more room for my junk (priceless parts collection) and at the same time store my creations, but there is never enough room, so often bikes are recycled for parts after a year or two. This constant shuffling of stuff then leads to my ever present lack of time, and often I just let things pile up and work around the mess since a full cleaning would take most of the day away.

After we moved into a single wide modular home, I knew that my indoor workspace would need more a lot more room; it was time for some basement renos. I have a fair collection of electronic bits for my work, so storage space and workbench room are very important. I decided to turn one end of the basement into a lab. It’s always fun to share photos of our workspaces, and since I have blogged about my old bike building shack down at the bottom of the hill, I thought it would be fun to show the space I am occupying as I write this now. The lab!

Anyone who has been in a modular home knows that they are 16 feet wide and long, really long! We decided to custom design the modular to sit on a full 9 foot basement so that we would double our space and end up with huge windows, making it seem less like a basement and more like a split level. The engineered trusses are great because all of the ductwork is out of the way, 9 feet about the floor level.

All of my electronics parts, robot bits, and good bike parts ended up in the basement, since we have very little outdoor storage space. The AZ parts orders are also packed down here on the brown table. There is a decent amount of space here, but I have not had much time to organize it or do any work. I did however, get to complete my new lab recently and am typing out at you from it right now.

Working with wood instead of steel

 

When you are a DIY type, it doesn’t matter what materials or tools you are using – you just measure three times, cut once and adapt along the way. Working with wood is certainly easier than steel, but doing a proper renovation does take a lot of research into code. Living in a Northern climate and having a 5 foot concrete wall with a 4 foot stud wall on top took some amount of planning in order to get the insulation done correctly. I had to build another 2×6 wall an inch ahead of the concrete wall and create an air barrier on the cold side then a vapor barrier on the warm side, keeping to an R24 insulation value.

Sure, I know what I am talking about now, but when I started, I didn’t know the deference between an air barrier and a moisture barrier. A moldy basement was not something I wanted, so I did my research. The secondary wall took out about a foot from the width of the room, but it still ended up being 14×16, and that was certainly enough room for me to work on my technical projects and plan writing.

My new lab partially completed

 

I continued the secondary wall up to the top, added a suspension ceiling, lights, lots of electrical and then put down a waterproof composite floor that looked like hardwood. I was quite happy with the final results, considering much of the things I did were new to me. I still need to finish building the cupboards and workbenches, but I am quite comfortable on the temporary tables and have plenty of room to store my stuff.

So, if time permits, I will once again expand my space, enjoying the rewards of DIY and learning new skills as I move along.  No doubt, if you are the type of person who would build a bike, you probably enjoy other DIY projects as well around the house and yard. DIY is a way of life!

~ Brad

Random thoughts, more rain!

Managed to snap a pic in between storms.

 

It’s official; we now live in the rain forest! And, when it’s not raining, the humidity hovers between 70 and 80 percent, so it might as well be. Oh well, here I am complaining about the rain when three months ago I was up to my waistline in snow. I guess that spring and fall really are the only good seasons for an outdoor bike hacker like me.

I did manage to get an hour on the Transporter Cargo Bike and added the cables, levers, and shifters. The first test run went well minus the fact that I had almost no air on the front tire. To complete the plan, I still have to get some photos and video of the bike being loaded with cargo, so it will be a game of waiting for the weather to cooperate.

Wow, a day that might not rain!

 

This week’s forecast is pretty much the same as the last two months with 40 to 60 percent chance of showers, which really means spitting rain every hour followed by intense rain for a few minutes and then 70 percent humidity until the next wave of rain. I don’t ever remember this much rain, and I am seeing plant life that looks like it belongs in the Amazon jungle around here.

New welding and grinding tutorials coming

 

In an effort to do something useful this year, we have decided to start making some highly detailed welding and grinding tutorials to replace the old ones on our website. These will be step-by-step video and photo tutorials from the very beginning that will show a noob what kind of welder and gear he or she might need, right up to controlling distortion. Since bike building seems nearly impossible out here this year, I plan to retro fit the non-leaky side of my shack with some backing boards and turn it into a video studio to make the new tutorials.

I will be purchasing a MIG welder as well for the tutorials since many are using one and will go through the process of both arc welding and MIG welding in great detail. Grinding tutorials will be the same in depth video and photo tutorials with hundreds of images lots of example videos, and text that explains everything one would ever need to know in order to jump head first into this great hobby.

A robot project from 2001

 

I like to dig through my old photo archives when I am doing my morning blog. Here is a real retro photo of one of my first large robot projects. If you can drag your gaze away from my super cool sideburns for a second, then you will see that I am riding on the robot, with an RF controller in my hand during a test run of the differentially steered transmission system. This robot was quite unstable and dangerous since it could reach speeds of 20 miles per hour and then flop over face first when something glitched in the motor drive processor!

But, the robot was fun to operate. I would sit indoors looking at a video link being transmitted from the head mounted camera and navigate (carefully) around the block, interacting with stunned bystanders using a text to speech processor that made the robot talk. I do miss building these things. Once I have an indoor workspace again, I have plans to build a 4×4 autonomous robot that will patrol our yard and keep that dumb bear off the property.

Well, I am going to head our and face the rainforest now. I have to find a way to cut the lawn in between drizzle as it is now knee high in most areas. Talk at ya later.

~ Brad

Paper, Proto, Plan, Precipitation!

A tandem tadpole trike sketch

I was really hoping to have the Transporter Cargo Bike ready to show off for this morning’s blog, so far this year has turned our area into a rain forest. Sure, it’s great for the garden and berry trees, but not great for getting any welding or building time in because my shack has no doors or windows and leaks when it rains. Add to that the 2 foot tall grass and I am starting to wonder if perhaps winter would be more productive after all! OK, enough complaining I will save that for the end of the blog!

While searching for something else to blog about, I thought of what it takes to turn an idea into a working project. I divide the process into three steps: paper, prototype and then plan. Most of the time, an idea never leaves the paper stage. I currently have 43 full spiral ringed notebooks of bike ideas that I have collected from over the last five years. Sadly, I never kept notebooks before that time, so a lot of cool and crazy ideas ended up in the recycle bin.

I usually start with a few pages of rough sketching just to get my head around the basic idea and how it might look.  It takes only a few minutes to sketch up a bike. The sketches offer a decent view of many of the difficulties in designing a bike or trike such as chain line, seating position and steering. I can usually determine if an idea is viable within a few pages worth of sketching, and by the 10th drawing often the bike or trike is radically different than the original idea. This tandem tadpole trike sketch seemed workable, so it was one of the few drawings from several thousand that moved to stage two – prototype.

The Viking Tandem Trike

All of the AZ plans go through a prototype stage so that ideas can be tested in the real world and then either modified or scrapped. Having a rough prototype means I can beat the hell out of the vehicle and see what it can take, making any adjustments that may be necessary. This tandem trike proto was made of electrical conduit and BMX wheels and took about two weekends to put together. We tested this trike at a campground for three days, beating it up over trails, down rough gravel roads, and even off road at times. It held up, even though there was no frame trussing and many of the welds were only half finished. My thinking is that if a poorly build proto can hold up to abuse, then a properly built final design would certainly hold up to just about any conditions. So, the next step was to turn proto into plan.

Turning paper into prototype

When I built the Viking Tandem Trike based on the original prototype, I made it a lot more durable and added many new features such as an unlinked transmission system, adjustable bottom brackets, dual disc brakes and under seat steering. The 1.25 inch conduit was replaced by 2 inch square tubing and the frame was properly triangulated for supreme strength. Building a plan from a prototype is a much longer process because every step has to be meticulously photographed and documented, but it is worth the effort when I see completed projects based on our plans being posted in the gallery.

So I am 95% into the plan stage on the Transporter Cargo Bike and only need to add the brake and shifter cables to complete the plan. But, the rain-man seems to have other plans, keeping me indoors as of late.

This is a typical site out here lately

The weather report has been practically the exact same for more than a month – a 40% chance of thunder showers and high humidity. What that means is that it spits rain once every few hours and dumps rain once a day. The grass is constantly wet, and my bike building shack smells like the back of uncle Jeb’s cabin…ack! I am at the point where I need a nice dry sunny day to get the final photos done, even if the rain holds off for four hours, I would be happy. Oh well, the apples and berry trees are sure enjoying the new rain forest, but the lawn is getting so tall it may take three days to hand mow the yard the next chance I get! I wonder, is there such a thing as an anti-rain dance?

~ Brad

DIY always gets attention

I’ve always had a passion for radical bike designs.

If you have been hacking things together for any length of time, then you probably know that your unique creations draw attention wherever you are. When I was in my early teens, I would string four or five scrap bikes together and my buddies and I would wobble down the street on my contraptions that often resembled bikes from Doctor Seuss books. Making it back home in one piece was a 50/50 chance because I usually only brazed my early bike hacks, but the one thing that was guaranteed was a lot of attention.  My intent was never to make something to draw a crowd, but I often found myself talking to a group of interested onlookers or even speaking into the camera on the evening news.

I took a long break from bike hacking after getting my first motorcycle (and job), but found myself back out in the garage in the year 2000 to rekindle my DIY roots and get my mind off the daily grind of living in the real world. I started collecting junk bikes and old power chair parts and concocted some cool bikes and robots out in the small garage just to have fun on the weekend. Oddly enough, I never took any photos or intended to publish these works. One day Kat suggested that I put some of the bikes up on my website AtomicZombie.com, which at the time was a home for electronics hacking stuff I was doing.

Getting youth interested in technology.

 

Well, within months I started connecting with some amazing people and realized I wasn’t the only one who enjoyed making art from metal, sometimes for fun, sometimes to be practical. It didn’t take long before the word spread locally, and we were dragging my creations to all kinds of events. The large video guided robots were always popular. I enjoyed inspiring young hackers to consider this great hobby. The robots were a natural crowd magnet since I controlled them from miles away via video link and could communicate to people by typing words into a speech synthesis station at the base, making the robot seem intelligent. Soon my remote robots’ main purpose was to draw in a crowd and baffle them with technology.

Photo op with some visiting teens from the USA after my World Record ride.

At one point, I decided to aim for a Guinness World Record, making the tallest rideable bicycle, and figure it would be fun and possible draw a bit of attention to the website which was now mostly dedicated to bike building. Well, I was certainly not ready for the storm that this thing generated once the word got out! I must have done a dozen live radio interviews, news casts and even a live spot on a a national broadcast of Canada AM . Tall bikes sure draw the crowds!

When the tallbike called “SkyCycle” made it to a full color page in the Guinness Book (along with my mug), I was shocked. I knew these crazy contraptions could draw interest, but I had no idea how far it could go. Even a simple recumbent bike like the Marauder would spend half the time parked as I explained the bike to interested people along a ride. No doubt, all you DIY enthusiast out there know what I am talking about.

When I think back to me pre-DIY days, I guess my inspiration did come from seeing others’ creations, although it was mostly in the form of photos from old Popular Mechanics books or the odd newspaper article. Now, with the internet jacked into our heads like The Matrix, it’s so easy to connect with other DIY folks and share advice, so the community is stronger than it’s even been. Back in the early 1980s I would have never thought that one day I would be saying, “Hey!” to a cargo bike builder in Africa and then a trike builder in Australia within a 15 minute span.

So, if you are a new builder just getting ready to roll open that garage door and head out on your new DIY creation, get prepared for the attention your work will draw.  You will now become the source of inspiration for a young generation of future DIYers, so make sure you pass along that attitude that drives us all, “Yeah, you can do this, too”!

~ Brad